Liquid Distributors for Packed Columns

A packed column can only perform as well as its initial liquid distribution. If liquid enters the bed unevenly, part of the packing works while the rest is bypassed — and no packing, however good, recovers that loss. We build trough, orifice and spray distributors to suit your liquid rate, turndown and column size, and we match the mounting ring and manway dimensions of the vessel you already have.

Types & Configurations

Trough (overflow) distributor

Liquid is fed into open troughs and overflows through notches or downcomer tubes onto the bed. Handles high liquid loads and large column diameters, and stays serviceable because it can be entered and cleaned. Distribution quality depends on the troughs being set truly level.

Orifice pan / perforated pipe distributor

Liquid stands on a pan or inside a header and passes through calibrated orifices. Simple, compact and predictable, with good turndown when the orifice count is designed for it. Best suited to clean liquids, since small orifices are the first thing to plug.

Spray (nozzle) distributor

A header with nozzles sprays liquid over the bed. Lowest cost and lowest pressure-drop option, useful for low liquid rates, scrubbers and applications where the packing only needs to be kept wet. Distribution is coarser than a trough or pan and is sensitive to gas cross-flow.

Specifications

ParameterDetail
ConfigurationTrough / overflow, orifice pan, perforated pipe, spray header
MaterialsSS304, SS316L, duplex, PP, PVDF, PTFE-lined steel, FRP
Design inputs we needLiquid rate, turndown ratio, column ID, nozzle size and orientation, vapour rate
MountingSupport ring or welded brackets, levelled at site; segmented for manway entry
Distribution pointsSet by design practice for your turndown and bed diameter
FabricationRemovable sections, lifting lugs, matched to existing bolt pattern where required

Available Materials

SS304 · SS316L · Duplex stainless steel · PP · PVDF · PTFE-lined steel · FRP

Typical Applications

  • Distillation and fractionation columns
  • Absorption and gas scrubbing towers
  • Strippers and wastewater desorption columns
  • Quench and cooling towers
  • Columns with high turndown or intermittent operation

Selection & Design Notes

  • Give us the minimum and maximum liquid rate, not just the design point — turndown decides whether a pan with fewer, larger orifices or a trough arrangement is the right answer.
  • Tell us the column internal diameter, manway size and whether the distributor must be installed through it. Anything larger than the manway has to be built in sections that bolt together inside the vessel.
  • Liquid with suspended solids or tendency to crystallise should not go through small orifices. In that service a trough or a large-hole design with a purge connection is safer.
  • Levelness is not a detail: a distributor set out of level will feed one side of the bed harder than the other for its whole service life. We supply levelling references and installation tolerance with the drawings.
  • If the column already exists, send the support ring detail or a sketch. Matching the vessel is cheaper than modifying it.

How the Options Compare

Trough distributors are the default for large columns and high liquid loads; orifice pans give more predictable distribution in smaller, clean-service columns; spray headers are the economical choice for scrubbers and low liquid rates. Where turndown is wide, a trough or a two-stage arrangement usually holds distribution better than a single orifice plate.

Frequently Asked Questions

How do I know which distributor type suits my column?

The deciding inputs are liquid rate, turndown, column diameter and how clean the liquid is. Send those four and we will tell you which type is realistic — in many cases two of them work, and the choice then comes down to cost and serviceability.

Can you replace a distributor in an existing column?

Yes. We work from the support ring detail, nozzle arrangement and a sketch or photos of the existing internals. The replacement is built to drop into the same space, so no vessel modification is needed.

Will a spray header give the same efficiency as a trough distributor?

Not usually in a tightly specified distillation column. Spray distribution is coarser and affected by gas flow, so it is normally chosen for scrubbing and wetting duties where exact distribution is less critical.

What information do you need to quote?

Liquid rate range, column diameter, service fluid, material, nozzle size, and whether the unit is new or a replacement. A P&ID extract or column datasheet makes the quotation precise.

Other Tower Internals

Support Plates

Packing support plates and support grids for random and structured packing: bar grids, perforated plates and c…

Redistributors

Collector and chimney-tray liquid redistributors for tall packed beds. Re-mix liquid, correct wall flow and su…

Demister Supports

Support grids and hold-down bars for wire mesh and vane mist eliminators. Prevent pad sag and gas bypass, allo…

Feed Pipes & Baffles

Feed pipes, inlet distributors and impingement baffles that protect packed beds from high-velocity impingement…

Talk to us about liquid distributors

Tell us your flow rate, medium and operating conditions — we recommend the right packing and internals, and quote factory-direct.

Request a Quote WhatsApp