Demister Supports, Grids & Hold-Down Bars

A mist eliminator only removes what passes through it. If the pad sags, lifts, or lets gas slip around its edge, droplets go straight up the wall and the separator "fails" without anything being wrong with the mesh itself. The support grid and hold-down bars are what keep the element in place, square to the flow, with a seal at the vessel wall — and they have to drain freely while doing it.

Types & Configurations

Support grid (upflow)

A grid or bar structure under the mesh pad, sized to carry the wet pad weight without sagging between supports. Open area is kept high so drained liquid does not pond on the grid.

Hold-down grid / bars

Fitted above the pad to stop it lifting or fluidising at high gas velocity. Usually lighter than the support grid, with the same open-area requirement.

Vane pack support frame

A frame that carries vane bundles at the correct angle and spacing, with drainage channels so separated liquid leaves the pack instead of being re-entrained.

Wall seal and bypass prevention

Ring detail, gasket or packed seal between the element edge and the vessel wall. This is the single most common cause of poor demister performance in service.

Specifications

ParameterDetail
TypeSupport grid, hold-down grid, vane pack frame, wall seal ring
MaterialsSS304, SS316L, duplex, PP, PVDF, PTFE, FRP
Design inputsVessel ID, demister type and thickness, gas velocity, liquid load
Open areaHigh free area to avoid ponding and hold-up on the grid
SegmentationSplit for manway entry; bolted joints inside the vessel
AccessoriesLifting handles, fasteners in matching material, gaskets

Available Materials

SS304 · SS316L · Duplex stainless steel · PP · PVDF · PTFE · FRP

Typical Applications

  • Knock-out drums and separator vessels
  • Absorber and scrubber tops
  • Evaporator and crystalliser vapour outlets
  • Compressor suction scrubbers
  • Columns with wire mesh or vane mist eliminators

Selection & Design Notes

  • Give us the gas velocity at the design case and the turndown case. Hold-down requirements come from the highest velocity the pad will see, not the average.
  • Say which way the flow runs. Upflow needs a hold-down grid as well as a support; downflow does not.
  • Drainage path matters as much as strength. A grid that traps liquid re-entrains it into the gas, which reads as a demister failure even though the mesh is fine.
  • The wall seal is not optional. Specify how the element edge closes against the vessel — a few millimetres of gap is enough for a measurable bypass.
  • If the vessel is already built, send the nozzle and support ring dimensions. Most retrofits fail on fit, not on design.

How the Options Compare

A support grid alone is enough for low-velocity upflow duty. Add a hold-down grid wherever gas velocity could lift the pad, which is most revamps and most high-capacity scrubbers. Vane packs need a purpose-built frame with drainage rather than a grid, because their separation depends on the gas turning inside the bundle.

Frequently Asked Questions

Do I need a hold-down grid as well as a support grid?

For upflow service at meaningful gas velocity, usually yes. The support grid carries the wet pad; the hold-down stops it lifting and channelling. Downflow installations normally need only support.

Why does my demister pass liquid even though the pad looks intact?

The usual causes are gas bypassing around the element edge, the pad sagging away from the support, or liquid re-entrainment from a grid that does not drain. All three are support and installation issues rather than mesh issues.

Can you supply the grids with the demister pad?

Yes. Supplying mesh, vane pack and support as one item removes the fit risk and the argument over who is responsible when performance falls short.

What material suits a chlorinated or acidic vapour?

SS316L for many chloride duties, PP/PVDF or PTFE where stainless is attacked, and FRP in some scrubbing services. Send the medium, concentration and temperature for a recommendation.

Other Tower Internals

Liquid Distributors

Factory-direct liquid distributors for packed columns: trough, orifice pan and spray types in SS304, SS316L, P…

Support Plates

Packing support plates and support grids for random and structured packing: bar grids, perforated plates and c…

Redistributors

Collector and chimney-tray liquid redistributors for tall packed beds. Re-mix liquid, correct wall flow and su…

Feed Pipes & Baffles

Feed pipes, inlet distributors and impingement baffles that protect packed beds from high-velocity impingement…

Talk to us about demister supports

Tell us your flow rate, medium and operating conditions — we recommend the right packing and internals, and quote factory-direct.

Request a Quote WhatsApp